HTML PUBLIC "-//W3C//DTD HTML 4.01 Transitional//EN"EN
26.5.2011 Official
Journal
of
the
European
Union L
139/1
II
(Non-legislative acts)
DECISIONS
COMMISSION DECISION
of 26 April 2011
concerning a technical specification for interoperability relating to the rolling stock subsystem —
‘Locomotives and passenger rolling stock’ of the trans-European conventional rail system
(notified under document C(2011) 2737)
(Text with EEA relevance)
(2011/291/EU)
THE EUROPEAN COMMISSION,
should cover the rolling stock subsystem in order to
meet the essential requirements and ensure the interoper
ability of the rail system.
Having regard to the Treaty on the Functioning of the European
Union,
(4)
The TSI on rolling stock to be set up by this Decision
does not fully deal with all essential requirements. In
Having regard to Directive 2008/57/EC of the European
accordance with Article 5(6) of Directive 2008/57/EC,
Parliament and the Council of 17 June 2008 on the interoper
technical aspects which are not covered should be
ability of the rail system within the Community ( 1 ), and in
identified as open points.
particular Article 6(1) thereof,
Whereas:
(5) The
TSI
on
rolling
stock
should
refer
to
Commission
Decision 2010/713/EU of 9 November 2010 on
modules for the procedures for assessment of
(1) In
accordance
with
Article
2(e)
and
Annex
II
of
Directive
conformity, suitability for use and EC verification to be
2008/57/EC, the rail system is subdivided into structural
used in the technical specifications for interoperability
and functional subsystems, including a rolling stock
adopted under Directive 2008/57/EC of the European
subsystem.
Parliament and of the Council ( 3 ).
(2) By
Decision
C(2006)
124
final
of
9
February
2007,
the (6) In accordance with Article 17(3) of Directive
Commission gave a mandate to the European Railway
2008/57/EC, Member States are to notify to the
Agency (hereinafter ‘the Agency’) to develop technical
Commission and other Member States the technical
specifications for interoperability (TSIs) under Directive
rules, the conformity assessment and verification
2001/16/EC of the European Parliament and of the
procedures to be used for the specific cases, as well as
Council of 19 March 2001 on the interoperability of
the bodies responsible for carrying out these procedures.
the trans-European conventional rail system ( 2 ). Under
the terms of that mandate, the Agency was requested
to draw up the draft TSIs related to passenger carriages
and locomotives and traction units, related to the rolling
(7) Commission
Decision
2008/163/EC
of
20
December
stock subsystem of the conventional rail system.
2007 concerning the technical specification of interoper
ability relating to ‘safety in railway tunnels’ in the trans-
European conventional and high-speed rail system ( 4 ),
(3) Technical
specifications
for
interoperability
(TSIs)
are
includes in its scope some requirements of the rolling
specifications adopted in accordance with Directive
stock running in the conventional rail system.
2008/57/EC. The TSI to be set up by this Decision
Therefore Decision 2008/163/EC should be amended
( 1 ) OJ L 191, 18.7.2008, p. 1.
( 3 ) OJ L 319, 4.12.2010, p. 1.
( 2 ) OJ L 110, 20.4.2001, p. 1.
( 4 ) OJ L 64, 7.3.2008, p. 1.

---

L 139/2
EN
Official Journal of the European Union
26.5.2011
(8)
The TSI on rolling stock should be without prejudice to
(c) rolling stock of an existing design, as referred to in clause
the provisions of other relevant TSIs which may be
7.1.1.2.4 of the TSI set out in the Annex.
applicable to rolling stock subsystems.
Article 3
(9)
The TSI on rolling stock should not impose the use of
specific technologies or technical solutions except where
1. With
regard
to
those
issues
classified
as
open
points
set
this is strictly necessary for the interoperability of the rail
out in the TSI set out in the Annex, the conditions to be
system within the European Union.
complied with for the verification of the interoperability
pursuant to Article 17(2) of Directive 2008/57/EC shall be
the applicable technical rules in use in the Member State
(10) In accordance with Article 11(5) of Directive
which authorises the placing in service of the subsystems
2008/57/EC, the TSI on rolling stock should allow, for
covered by this Decision.
a limited period of time, for interoperability constituents
to be incorporated into subsystems without certification
if certain conditions are met.
2. Each
Member
State
shall
notify
to
the
other
Member
States and to the Commission within six months of the notifi
cation of this Decision:
(11) To continue to encourage innovation and to take into
account the experience acquired, this Decision should be
subject to periodic revision.
(a) the applicable technical rules referred to in paragraph 1;
(12) The
provisions
of
this
Decision
are
in
conformity
with
the opinion of the Committee set up by Article 21 of
Council Directive 96/48/EC (
(b) the conformity assessment and checking procedures to be

1 ),
applied with regard to the application of the technical rules
referred to in paragraph 1;
HAS ADOPTED THIS DECISION:
(c) the bodies it appoints for carrying out the conformity
Article 1
assessment and checking procedures of the open points
The technical specification for interoperability (TSI) relating to
referred to in paragraph 1.
the rolling stock subsystem, ‘Locomotive and passenger rolling
stock’, of the trans-European conventional railway system as set
out in the Annex is hereby adopted.
3. With regard to the national rules applicable to vehicles
categorised for national use in section 4.2.3.5.2.2, paragraph 2
of this Article also applies.
Article 2
1. The
TSI
set
out
in
the
Annex
shall
apply
to
all
new
rolling
stock of the trans-European conventional rail system as defined
Article 4
in Annex I to Directive 2008/57/EC. The technical and
geographical scope of this Decision is set out in Sections 1.1
1. With
regard
to
those
issues
classified
as
specific
cases
set
and 1.2 of the Annex.
out in Section 7 of the TSI set out in the Annex, the conditions
to be complied with for the verification of the interoperability
pursuant to Article 17(2) of Directive 2008/57/EC shall be the
The TSI set out in the Annex shall also apply to existing rolling
applicable technical rules in use in the Member State which
stock when it is subject to renewal or upgrading in accordance
authorises the placing in service of the subsystems covered by
with Article 20 of Directive 2008/57/EC.
this Decision.
2. Until
1
June
2017,
the
application
of
this
TSI
shall
not
be
2. Each
Member
State
shall
notify
to
the
other
Member
compulsory for the following rolling stock:
States and to the Commission within six months of the notifi
cation of this Decision:
(a) projects at an advanced stage of development, as referred to
in clause 7.1.1.2.2 of the TSI set out in the Annex;
(a) the applicable technical rules referred to in paragraph 1;
(b) contracts in course of performance, as referred to in clause
7.1.1.2.3 of the TSI set out in the Annex;
(b) the conformity assessment and checking procedures to be
applied with regard to the application of the technical rules
( 1 ) OJ L 235, 17.9.1996, p. 6.
referred to in paragraph 1;

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/3
(c) the bodies it appoints for carrying out the conformity
Article 8
assessment and checking procedures of the specific cases
referred to in paragraph 1.
Amendments to Decision 2008/163/EC
Decision 2008/163/EC is amended as follows:
Article 5
1. the following text is inserted after the second paragraph of
The procedures for assessment of conformity, suitability for use
point 4.2.5.1 Material properties for rolling stock:
and EC verification set out in Section 6 of the TSI set out in the
Annex shall be based on the modules defined in Decision
2010/713/EU.
‘In addition, the requirements of clause 4.2.10.2 (Material
requirements) of the CR LOC & PAS TSI shall apply to CR
rolling stock.’;
Article 6
1. An
EC
certificate
of
verification
for
a
subsystem
that 2. point 4.2.5.4 is replaced by the following:
contains interoperability constituents not holding an EC
declaration of conformity or suitability for use may be issued
during a transition period of six years from the date of appli
cation of this Decision, on the condition that the provisions set
‘4.2.5.4. Fire barriers for passenger rolling stock
out in Section 6.3 of the Annex are met.
— The requirements of clause 4.2.7.2.3.3 (Fire
resistance) of the high-speed RST TSI apply to
2. The
production
or
upgrade/renewal
of
the
subsystem
with
HS rolling stock.
use of the non-certified interoperability constituents must be
completed within the transition period, including the placing
in service.
— The requirements of clause 4.2.7.2.3.3 (Fire
resistance) of the high-speed RST TSI and the
requirements of clause 4.2.10.5 (Fire barriers)
3. During
the
transition
period
Member
States
shall
ensure
of the conventional LOC & PAS TSI apply to
that:
CR rolling stock.’;
3. point 4.2.5.7 is replaced by the following:
(a) the reasons for non-certification of the interoperability
constituents are properly identified in the verification
procedure referred to in paragraph 1;
‘4.2.5.7. Communication means on trains
(b) the details of the non-certified interoperability constituents
— The requirements of clause 4.2.5.1 (Public
and the reasons for non-certification, including the appli
address system) of the high-speed RST TSI
cation of national rules notified under Article 17 of
apply to HS rolling stock.
Directive 2008/57/EC, are included by the national safety
authorities in their annual report referred to in Article 18 of
Directive 2004/49/EC of the European Parliament and of
— The requirements of clause 4.2.5.2 (Public
the Council ( 1 ).
address system: audible communication system)
of the conventional LOC & PAS TSI apply to CR
rolling stock.’;
4. After
the
transition
period
and
with
the
exceptions
allowed under Section 6.3.3 of the Annex on maintenance,
interoperability constituents shall be covered by the required
4. point 4.2.5.8 is replaced by the following:
EC declaration of conformity and/or suitability for use before
being incorporated into the subsystem.
‘4.2.5.8. Emergency brake override
Article 7
— The requirements in clause 4.2.5.3 (Passenger
With regard to the rolling stock concerned by projects at
alarm) of the high-speed RST TSI apply to HS
advanced stage of development, each Member State shall
rolling stock.
communicate to the Commission within one year of entry
into force of this Decision a list of projects that are taking
place within its territory and are at an advanced stage of devel
— The requirements in clause 4.2.5.3 (Passenger
opment.
alarm: functional requirements) of the conven
tional LOC & PAS TSI apply to CR rolling
( 1 ) OJ L 164, 30.4.2004, p. 44.
stock.’;

---

L 139/4
EN
Official Journal of the European Union
26.5.2011
5. point 4.2.5.11.1 is replaced by the following:
Article 9
This Decision shall apply from 1 June 2011.
‘4.2.5.11.1. Passengers’ emergency exits
Article 10
This Decision is addressed to the Member States.
— The requirements in clause 4.2.7.1.1
(Passengers’ emergency exits) of the high-
speed RST TSI apply to HS rolling stock.
Done at Brussels, 26 April 2011.
For the Commission
— The requirements in clause 4.2.10.4
(Passenger evacuation) of the conventional
Siim KALLAS
LOC & PAS TSI apply to CR rolling stock.’.
Vice-President

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/5
ANNEX
DIRECTIVE 2008/57/EC ON THE INTEROPERABILITY OF THE RAIL SYSTEM WITHIN THE COMMUNITY
TECHNICAL SPECIFICATION FOR INTEROPERABILITY
‘Rolling stock’ subsystem for conventional rail ‘Locomotives and passenger rolling stock’
Page
1.
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
1.1.
Technical scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
1.2.
Geographical scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
1.3.
Content of this TSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
1.4.
Referenced documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
2.
ROLLING STOCK SUBSYSTEM AND FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17
2.1.
The rolling stock subsystem as part of the conventional rail system . . . . . . . . . . . . . . . . . . .
17
2.2.
Definitions related to rolling stock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
2.3.
Rolling stock in the scope of this TSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19
3.
ESSENTIAL REQUIREMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
3.1.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
3.2.
Elements of the rolling stock subsystem corresponding to the essential requirements . . . . . . .
21
3.3.
Essential requirements not covered by this TSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25
3.3.1.
General requirements, requirements related to maintenance and operation . . . . . . . . . . . . . . .
25
3.3.2.
Requirements specific to other subsystems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
4.
CHARACTERISATION OF THE ROLLING STOCK SUBSYSTEM . . . . . . . . . . . . . . . . . . . . . . .
26
4.1.
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
4.1.1.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
4.1.2.
Description of the rolling stock subject to the application of this TSI . . . . . . . . . . . . . . . . . .
26
4.1.3.
Main categorisation of the rolling stock for application of TSI requirements . . . . . . . . . . . . .
26
4.1.4.
Categorisation of the rolling stock for fire safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
4.2.
Functional and technical specification of the subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
4.2.1.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
4.2.1.1.
Breakdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
4.2.1.2.
Open points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
4.2.1.3.
Safety aspects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
4.2.2.
Structure and mechanical parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
4.2.2.1.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
4.2.2.2.
Mechanical interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
4.2.2.2.1.
General and definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
4.2.2.2.2.
Inner coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
29
4.2.2.2.3.
End coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
4.2.2.2.4.
Rescue coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
4.2.2.2.5.
Staff access for coupling and uncoupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31

---

L 139/6
EN
Official Journal of the European Union
26.5.2011
Page
4.2.2.3.
Gangways . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
31
4.2.2.4.
Strength of vehicle structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32
4.2.2.5.
Passive safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32
4.2.2.6.
Lifting and jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
4.2.2.7.
Fixing of devices to car body structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
4.2.2.8.
Staff and freight access doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
4.2.2.9.
Mechanical characteristics of glass (other than windscreens) . . . . . . . . . . . . . . . . . . . . . . . . . .
34
4.2.2.10.
Load conditions and weighted mass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
4.2.3.
Track interaction and gauging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
4.2.3.1.
Gauging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
4.2.3.2.
Axle load and wheel load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
4.2.3.2.1.
Axle load parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
4.2.3.2.2.
Wheel load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
4.2.3.3.
Rolling stock parameters which influence ground based systems . . . . . . . . . . . . . . . . . . . . . .
35
4.2.3.3.1.
Rolling stock characteristics for the compatibility with train detection systems . . . . . . . . . . . .
35
4.2.3.3.1.1. Rolling
stock
characteristics
for
compatiblility
with
train
detection
system
based
on
track
circuits 35
4.2.3.3.1.2.
Rolling stock characteristics for compatiblility with train detection system based on axle counters
36
4.2.3.3.1.3.
Rolling stock characteristics for compatibility with loop equipment . . . . . . . . . . . . . . . . . . . .
37
4.2.3.3.2.
Axle bearing condition monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
37
4.2.3.4.
Rolling stock dynamic behaviour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
37
4.2.3.4.1.
Safety against derailment running on twisted track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
37
4.2.3.4.2.
Running dynamic behaviour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
37
4.2.3.4.2.1.
Limit values for running safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38
4.2.3.4.2.2.
Track loading limit values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
4.2.3.4.3.
Equivalent conicity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
4.2.3.4.3.1.
Design values for new wheel profiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
4.2.3.4.3.2.
In-service values of wheelset equivalent conicity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40
4.2.3.5.
Running gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40
4.2.3.5.1.
Structural design of bogie frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
40
4.2.3.5.2.
Wheelsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41
4.2.3.5.2.1.
Mechanical and geometric characteristics of wheelsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
41
4.2.3.5.2.2.
Mechanical and geometrical characteristics of wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
4.2.3.5.2.3.
Variable gauge wheelsets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
4.2.3.6.
Minimum curve radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
4.2.3.7.
Life guards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
44
4.2.4.
Braking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45
4.2.4.1.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45
4.2.4.2.
Main functional and safety requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.2.4.2.1.
Functional requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
45

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/7
Page
4.2.4.2.2.
Safety requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
4.2.4.3.
Type of brake system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
47
4.2.4.4.
Brake command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48
4.2.4.4.1.
Emergency braking command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48
4.2.4.4.2.
Service braking command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48
4.2.4.4.3.
Direct braking command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48
4.2.4.4.4.
Dynamic braking command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
48
4.2.4.4.5.
Parking braking command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
49
4.2.4.5.
Braking performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
49
4.2.4.5.1.
General requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
49
4.2.4.5.2.
Emergency braking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
49
4.2.4.5.3.
Service braking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50
4.2.4.5.4.
Calculations related to thermal capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51
4.2.4.5.5.
Parking brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51
4.2.4.6.
Wheel rail adhesion profile — Wheel slide protection system . . . . . . . . . . . . . . . . . . . . . . . .
51
4.2.4.6.1.
Limit of wheel rail adhesion profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
51
4.2.4.6.2.
Wheel slide protection system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
52
4.2.4.7.
Dynamic brake — Braking system linked to traction system . . . . . . . . . . . . . . . . . . . . . . . . .
52
4.2.4.8.
Braking system independent of adhesion conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
4.2.4.8.1.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
4.2.4.8.2.
Magnetic track brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
4.2.4.8.3.
Eddy current track brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
4.2.4.9.
Brake state and fault indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
4.2.4.10.
Brake requirements for rescue purposes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
4.2.5.
Passenger related items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
54
4.2.5.1.
Sanitary systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55
4.2.5.2.
Public address system: audible communication system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
56
4.2.5.3.
Passenger alarm: functional requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
4.2.5.4.
Safety instructions to passengers — Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
4.2.5.5.
Communication devices for passengers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
4.2.5.6.
Exterior doors: passenger access to and egress from rolling stock . . . . . . . . . . . . . . . . . . . . .
58
4.2.5.7.
Exterior door system construction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
60
4.2.5.8.
Inter-unit doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
60
4.2.5.9.
Internal air quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
60
4.2.5.10.
Body side windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
4.2.6.
Environmental conditions and aerodynamic effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
4.2.6.1.
Environmental conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
4.2.6.1.1.
Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61
4.2.6.1.2.
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
61

---

L 139/8
EN
Official Journal of the European Union
26.5.2011
Page
4.2.6.1.3.
Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
62
4.2.6.1.4.
Rain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
62
4.2.6.1.5.
Snow, ice and hail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
62
4.2.6.1.6.
Solar radiation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
63
4.2.6.1.7.
Resistance to pollution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
63
4.2.6.2.
Aerodynamic effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
63
4.2.6.2.1.
Slipstream effects on passengers on platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
4.2.6.2.2.
Slipstream effects on workers at the track side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
4.2.6.2.3.
Head pressure pulse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
64
4.2.6.2.4.
Maximum pressure variations in tunnels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
64
4.2.6.2.5.
Cross wind . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
64
4.2.7.
External lights and visible and audible warning devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65
4.2.7.1.
External lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65
4.2.7.1.1.
Head lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65
4.2.7.1.2.
Marker lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65
4.2.7.1.3.
Tail lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
65
4.2.7.1.4.
Lamp controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
66
4.2.7.2.
Horn (audible warning device) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
66
4.2.7.2.1.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
66
4.2.7.2.2.
Warning horn sound pressure levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
66
4.2.7.2.3.
Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
66
4.2.7.2.4.
Horn control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
66
4.2.8.
Traction and electrical equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
66
4.2.8.1.
Traction performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
66
4.2.8.1.1.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
66
4.2.8.1.2.
Requirements on performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
67
4.2.8.2.
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
67
4.2.8.2.1.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
67
4.2.8.2.2.
Operation within range of voltages and frequencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
67
4.2.8.2.3.
Regenerative brake with energy to the overhead contact line . . . . . . . . . . . . . . . . . . . . . . . . .
67
4.2.8.2.4.
Maximum power and current from the overhead contact line . . . . . . . . . . . . . . . . . . . . . . . .
67
4.2.8.2.5.
Maximum current at standstill for DC systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68
4.2.8.2.6.
Power factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68
4.2.8.2.7.
System energy disturbances for ac systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
4.2.8.2.8.
Energy consumption measuring function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68
4.2.8.2.9.
Requirements linked to pantograph . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68
4.2.8.2.9.1.
Working range in height of pantograph . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68
4.2.8.2.9.1.1. Height of interaction with contact wires (RST level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68
4.2.8.2.9.1.2. Working range in height of pantograph (IC level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/9
Page
4.2.8.2.9.2.
Pantograph head geometry (IC level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
68
4.2.8.2.9.2.1. Pantograph head geometry type 1 600 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
4.2.8.2.9.2.2. Pantograph head geometry type 1 950 mm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
4.2.8.2.9.3.
Pantograph current capacity (IC level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
69
4.2.8.2.9.4.
Contact strip (IC level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
69
4.2.8.2.9.4.1. Contact strip geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
69
4.2.8.2.9.4.2. Contact strip material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
69
4.2.8.2.9.4.3. Contact strip characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
69
4.2.8.2.9.5.
Pantograph static contact force (IC level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
69
4.2.8.2.9.6.
Pantograph contact force and dynamic behaviour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70
4.2.8.2.9.7.
Arrangement of pantographs (RST level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70
4.2.8.2.9.8.
Running through phase or system separation sections (RST level) . . . . . . . . . . . . . . . . . . . . .
70
4.2.8.2.9.9.
Insulation of pantograph from the vehicle (RST level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70
4.2.8.2.9.10. Pantograph lowering (RST level) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70
4.2.8.2.10.
Electrical protection of the train . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
71
4.2.8.3.
Diesel and other thermal traction system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
4.2.8.4.
Protection against electrical hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
71
4.2.9.
Driver’s cab and driver-machine interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
71
4.2.9.1.
Driver’s cab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
71
4.2.9.1.1.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
71
4.2.9.1.2.
Access and egress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
71
4.2.9.1.2.1.
Access and egress in operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
71
4.2.9.1.2.2.
Driver’s cab emergency exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
72
4.2.9.1.3.
External visibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
72
4.2.9.1.3.1.
Front visibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
72
4.2.9.1.3.2.
Rear and side view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
72
4.2.9.1.4.
Interior layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
72
4.2.9.1.5.
Driver’s seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
73
4.2.9.1.6.
Driver’s desk — Ergonomics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
73
4.2.9.1.7.
Climate control and air quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
73
4.2.9.1.8.
Internal lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
73
4.2.9.2.
Windscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
73
4.2.9.2.1.
Mechanical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
73
4.2.9.2.2.
Optical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
74
4.2.9.2.3.
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
74
4.2.9.3.
Driver machine interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
74
4.2.9.3.1.
Driver’s activity control function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
74
4.2.9.3.2.
Speed indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75
4.2.9.3.3.
Driver display unit and screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75

---

L 139/10
EN
Official Journal of the European Union
26.5.2011
Page
4.2.9.3.4.
Controls and indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75
4.2.9.3.5.
Labelling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75
4.2.9.3.6.
Remote control function from the ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
75
4.2.9.4.
Onboard tools and portable equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
76
4.2.9.5.
Storage facility for staff personal effects . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
76
4.2.9.6.
Recording device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
76
4.2.10.
Fire safety and evacuation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
76
4.2.10.1.
General and categorisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
76
4.2.10.1.1.
Requirements applicable to all units, except freight locomotives and OTMs: . . . . . . . . . . . . . .
76
4.2.10.1.2.
Requirements applicable to freight locomotives and OTMs: . . . . . . . . . . . . . . . . . . . . . . . . . .
77
4.2.10.1.3.
Requirements specified in the SRT TSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
77
4.2.10.2.
Material requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
78
4.2.10.3.
Specific measures for flammable liquids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
78
4.2.10.4.
Passenger evacuation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
78
4.2.10.5.
Fire barriers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
79
4.2.11.
Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
79
4.2.11.1.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
79
4.2.11.2.
Train exterior cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
79
4.2.11.2.1.
Cleaning of driver’s cab windscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
79
4.2.11.2.2.
Exterior cleaning through a washing plant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
79
4.2.11.3.
Toilet discharge system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
79
4.2.11.4.
Water refilling equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
4.2.11.5.
Interface for water refilling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
4.2.11.6.
Special requirements for stabling of trains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
4.2.11.7.
Refuelling equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
4.2.12.
Documentation for operation and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
4.2.12.1.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
4.2.12.2.
General documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
81
4.2.12.3.
Documentation related to maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
4.2.12.3.1.
The maintenance design justification file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
81
4.2.12.3.2.
The maintenance description file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
82
4.2.12.4.
Operating documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
83
4.2.12.5.
Lifting diagram and instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
83
4.2.12.6.
Rescue related descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
83
4.3.
Functional and technical specification of the interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
83
4.3.1.
Interface with energy subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
83
4.3.2.
Interface with infrastructure subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
4.3.3.
Interface with operation subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
85
4.3.4.
Interface with the control, command and signalling subsystem . . . . . . . . . . . . . . . . . . . . . . .
86

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/11
Page
4.3.5.
Interface with the telematic application for passengers subsystem . . . . . . . . . . . . . . . . . . . . .
86
4.4.
Operating rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
86
4.5.
Maintenance rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
87
4.6.
Professional competencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
87
4.7.
Health and safety conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
87
4.8.
European register of authorised types of vehicles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
88
5.
INTEROPERABILITY CONSTITUENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
89
5.1.
Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
89
5.2.
Innovative solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
89
5.3.
Interoperability constituent specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
5.3.1.
Rescue couplers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
89
5.3.2.
Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
5.3.3.
WSP (wheel slide protection system) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
5.3.4.
Head lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
5.3.5.
Marker lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
5.3.6.
Tail lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
5.3.7.
Horns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
5.3.8.
Pantograph . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
5.3.8.1.
Contact strips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
91
5.3.9.
Main circuit breaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
91
5.3.10.
Toilet discharge connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
91
5.3.11.
Inlet connection for water tanks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
91
6.
ASSESSMENT OF CONFORMITY OR SUITABILITY FOR USE . . . . . . . . . . . . . . . . . . . . . . . .
92
6.1.
Interoperability constituents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
92
6.1.1.
Conformity assessment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
92
6.1.2.
Conformity assessment procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
6.1.2.1.
Conformity assessment modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
92
6.1.2.2.
Particular assessment procedures for interoperability constituents . . . . . . . . . . . . . . . . . . . . . .
93
6.1.2.2.1.
Wheel slide protection system (clause 5.3.3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
93
6.1.2.2.2.
Head lights (clause 5.3.4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
93
6.1.2.2.3.
Marker lights (clause 5.3.5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
93
6.1.2.2.4.
Tail lights (clause 5.3.6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
93
6.1.2.2.5.
Horn (clause 5.3.7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
93
6.1.2.2.6.
Pantograph (clause 5.3.8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
93
6.1.2.2.7.
Contact strips (clause 5.3.8.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
94
6.1.2.3.
Project phases where assessment is required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
94
6.1.3.
Innovative solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
95
6.1.4.
Constituent requiring EC declarations against the HS RST TSI and against TSI . . . . . . . . . . . .
95
6.1.5.
Assessment of suitability for use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
95

---

L 139/12
EN
Official Journal of the European Union
26.5.2011
Page
6.2.
Rolling stock subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
96
6.2.1.
EC verification (general) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
96
6.2.2.
Conformity assessment procedures (modules) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
96
6.2.2.1.
Conformity assessment modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
96
6.2.2.2.
Particular assessment procedures for subsystems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
96
6.2.2.2.1.
Load conditions and weighted mass (clause 4.2.2.10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
96
6.2.2.2.2.
Gauging (clause 4.2.3.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
96
6.2.2.2.3.
Wheel load (clause 4.2.3.2.2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
96
6.2.2.2.4.
Braking — safety requirements (clause 4.2.4.2.2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
97
6.2.2.2.5.
Emergency braking (clause 4.2.4.5.2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
98
6.2.2.2.6.
Service braking (clause 4.2.4.5.3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
98
6.2.2.2.7.
Wheel slide protection system (clause 4.2.4.6.2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
6.2.2.2.8.
Sanitary systems (clause 4.2.5.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
98
6.2.2.2.9.
Internal air quality (clause 4.2.5.9 and clause 4.2.9.1.7) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
98
6.2.2.2.10.
Slipstream effects on passengers on platform (clause 4.2.6.2.1) . . . . . . . . . . . . . . . . . . . . . . .
98
6.2.2.2.11.
Slipstream effects on workers at track side (clause 4.2.6.2.2) . . . . . . . . . . . . . . . . . . . . . . . . .
99
6.2.2.2.12.
Head pressure pulse (clause 4.2.6.2.3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
99
6.2.2.2.13.
Maximum power and current from the overhead contact line (clause 4.2.8.2.4) . . . . . . . . . . .
99
6.2.2.2.14.
Power factor (clause 4.2.8.2.6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
99
6.2.2.2.15.
Current collection dynamic behaviour (clause 4.2.8.2.9.6) . . . . . . . . . . . . . . . . . . . . . . . . . . .
99
6.2.2.2.16.
Arrangement of pantographs (clause 4.2.8.2.9.7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
6.2.2.2.17.
Windscreen (clause 4.2.9.2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
99
6.2.2.2.18.
Fire barriers (clause 4.2.10.5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
99
6.2.2.3.
Project phases where assessment is required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
99
6.2.3.
Innovative solutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100
6.2.4.
Assessment of documentation requested for operation and maintenance . . . . . . . . . . . . . . . .
100
6.2.5.
Units requiring EC certificates against the HS RST TSI and against this TSI . . . . . . . . . . . . . .
100
6.2.6.
Assessment of units intended to be used in general operation . . . . . . . . . . . . . . . . . . . . . . . .
103
6.2.7.
Assessment of units intended to be used in pre-defined formation(s) . . . . . . . . . . . . . . . . . . .
103
6.2.8. Particular
case:
Assessment
of
units
intended
to
be
included
in
an
existing
fixed
formation
103
6.2.8.1.
Context . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
103
6.2.8.2.
Case of a TSI compliant fixed formation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
103
6.2.8.3.
Case of a non-TSI compliant fixed formation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
103
6.3.
Subsystem containing interoperability constituents not holding an EC declaration . . . . . . . . .
104
6.3.1.
Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
104
6.3.2.
Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
104
6.3.3.
Maintenance of the subsystems certified according to clause 6.3.1 . . . . . . . . . . . . . . . . . . . . .
104
7.
IMPLEMENTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
7.1.
General rules for implementation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/13
Page
7.1.1.
Application to newly built rolling stock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
7.1.1.1.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
104
7.1.1.2.
Transition period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
105
7.1.1.2.1.
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
105
7.1.1.2.2.
Projects at advanced stage of development . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
7.1.1.2.3.
Contracts in course of performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
105
7.1.1.2.4.
Rolling stock of an existing design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
105
7.1.1.3.
Application to OTMs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
106
7.1.1.4.
Interface with implementation of other TSIs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
106
7.1.2.
Renewal and upgrade of existing rolling stock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
106
7.1.2.1.
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
106
7.1.2.2.
Renewal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
106
7.1.2.3.
Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
107
7.1.3.
Rules related to the type or design examination certificates . . . . . . . . . . . . . . . . . . . . . . . . . .
107
7.1.3.1.
Rolling stock subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
107
7.1.3.2.
Interoperability constituents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
108
7.2.
Compatibility with other subsystems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
108
7.3.
Specific cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
108
7.3.1.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
108
7.3.2.
List of specific cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
109
7.3.2.1.
General specific cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
109
7.3.2.2.
Mechanical interfaces — End coupling (4.2.2.2.3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
109
7.3.2.3.
Gauging (4.2.3.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
109
7.3.2.4.
Axle bearing condition monitoring (4.2.3.3.2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
110
7.3.2.5.
Rolling stock dynamic behaviour (4.2.3.4) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
112
7.3.2.6.
Track loading limit values (4.2.3.4.2.2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
112
7.3.2.7.
Design values for new wheel profiles (4.2.3.4.3.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
112
7.3.2.8.
Wheelsets (4.2.3.5.2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
114
7.3.2.9.
Geometrical characteristics of wheels (4.2.3.5.2.2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
115
7.3.2.10.
Slipstream effects on passengers on platforms (4.2.6.2.1) . . . . . . . . . . . . . . . . . . . . . . . . . . .
115
7.3.2.11.
Head pressure pulse (4.2.6.2.3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
116
7.3.2.12.
Warning horn sound pressure levels (4.2.7.2.2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
116
7.3.2.13.
Power supply — General (4.2.8.2.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
116
7.3.2.14.
Operation within range of voltages and frequencies (4.2.8.2.2) . . . . . . . . . . . . . . . . . . . . . . .
116
7.3.2.15.
Working range in height of pantograph (4.2.8.2.9.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
116
7.3.2.16.
Pantograph head geometry (4.2.8.2.9.2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
7.3.2.17.
Pantograph contact force and dynamic behaviour (4.2.8.2.9.6) . . . . . . . . . . . . . . . . . . . . . . .
118
7.3.2.18.
Front visibility (4.2.9.1.3.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
118
7.3.2.19.
Driver’s desk — Ergonomics (4.2.9.1.6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118

---

L 139/14
EN
Official Journal of the European Union
26.5.2011
Page
7.3.2.20.
Material requirements (4.2.10.2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
119
7.3.2.21.
Interfaces for water refilling (4.2.11.5) and toilet discharge (4.2.11.3) . . . . . . . . . . . . . . . . . .
119
7.3.2.22.
Special requirement for stabling of trains (4.2.11.6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
121
7.3.2.23.
Refuelling equipment (4.2.11.7) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
121
7.4.
Specific environmental conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
7.5.
Aspects that have to be considered in the revision process or in other activities of the Agency
122
7.5.1.
Aspects related to a basic parameter in this TSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
122
7.5.1.1.
Axle load parameter (clause 4.2.3.2.1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
122
7.5.1.2.
Track loading limit value (clause 4.2.3.4.2.2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
7.5.1.3.
Aerodynamic effects (clause 4.2.6.2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
123
7.5.2.
Aspects not related to a basic parameter in this TSI but are subject to research projects . . . .
123
7.5.2.1.
Additional requirements for security reasons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
7.5.3.
Aspects relevant for the EU railway system but out of the scope of TSIs . . . . . . . . . . . . . . .
124
7.5.3.1.
Track interaction (clause 4.2.3) — Flange or rail lubrication . . . . . . . . . . . . . . . . . . . . . . . . .
124
ANNEX A:
BUFFERS AND SCREW COUPLING SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
125
A.1.
Buffers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
125
A.2.
Screw coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
125
A.3.
Interaction of draw- and buffing-gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
125
ANNEX B:
LIFTING AND JACKING POINTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
128
B.1.
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
128
B.1.1.
Re-railing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
128
B.1.2.
Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
128
B.1.3.
Jacking and lifting points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
128
B.2.
Impact of re-railing on the design of rolling stock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
128
B.3.
Location of jacking points on the structures of vehicles . . . . . . . . . . . . . . . . . . . . . . . . . . . .
128
B.4.
Geometry of jacking/lifting points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
B.4.1.
Permanent built-in jacking/lifting points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
B.4.2.
Removable jacking/lifting points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
129
B.5.
Securing running gears onto the underframe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
129
B.6.
Marking of rescue jacking (resp. lifting) points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
129
B.7.
Jacking and lifting instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
129
ANNEX C:
SPECIAL PROVISIONS FOR MOBILE RAILWAY INFRASTRUCTURE CONSTRUCTION AND
MAINTENANCE EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
130
C.1.
Strength of vehicle structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
130
C.2.
Lifting and jacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
130
C.3.
Running dynamic behaviour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
ANNEX D:
ENERGY METER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
132
ANNEX E:
ANTHROPOMETRIC MEASUREMENTS OF THE DRIVER . . . . . . . . . . . . . . . . . . . . . . . . . . .
135

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/15
Page
ANNEX F:
FRONT VISIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
136
F.1.
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
136
F.2.
Reference position of vehicle in relation to track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
136
F.3.
Reference position for the eyes of crew members . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
136
F.4.
Conditions of visibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
136
ANNEX G:
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
137
ANNEX H:
ASSESSMENT OF THE ROLLING STOCK SUBSYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
138
H.1.
Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
138
H.2.
Characteristics and modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
138
ANNEX I:
ASPECTS FOR WHICH THE TECHNICAL SPECIFICATION IS NOT AVAILABLE (OPEN POINTS)
145
ANNEX J:
STANDARDS OR NORMATIVE DOCUMENTS REFERRED TO IN THIS TSI . . . . . . . . . . . . .
148
1. INTRODUCTION
1.1. Technical
scope
This technical specification for interoperability (TSI) is a specification by which a particular subsystem is
addressed in order to meet the essential requirements and ensure the interoperability of the trans-European
conventional rail system as described in Directive 2008/57/EC.
The particular subsystem is the rolling stock of the trans-European conventional rail system referred to in
Annex I Section 1 of Directive 2008/57/EC.
This TSI also includes the rolling stock subsystem as defined in Annex II Section 2.6 of Directive
2008/57/EC and the related parts of the energy subsystem (‘onboard part of the electric consumptions
measuring equipment’ as defined in Annex II Section 2.2 of Directive 2008/57/EC) which corresponds to
the onboard part of the energy structural subsystem.
This TSI is applicable to rolling stock:
— which is (or is intended to be) operated on the rail network defined in the Section 1.2 ‘Geographical
scope’ of this TSI,
and
— which is of one of the following types (as defined in Annex I Section 1.2 of Directive 2008/57/EC):
— self-propelling thermal or electric trains,
— thermal or electric traction units,
— passenger carriages,
— mobile railway infrastructure construction and maintenance equipment.
More information about the rolling stock in the scope of this TSI is given in Section 2 of this Annex.
1.2. Geographical
scope
— The geographical scope of this TSI is the trans-European conventional rail system network (TEN) as
described in Annex I Section 1.1 ‘Network’ of Directive 2008/57/EC.
— The requirements for high speed rolling stock designed to operate on the Trans European High-Speed
Rail system as provided for in Annex I (2.2) of Directive 2008/57/EC, at maximum speed intended for
this high-speed network, are not covered in this TSI.

---

L 139/16
EN
Official Journal of the European Union
26.5.2011
— The additional requirements to this TSI that may be necessary for safe operation on high-speed
networks of conventional rolling stock of maximum speed lower than 190 km/h which are in the
scope of this TSI (as defined in clause 2.3 below) are identified as an open point in the current version
of this TSI.
1.3. Content
of
this
TSI
In accordance with Article 5(3) of Directive 2008/57/EC this TSI:
(a) indicates its intended scope (Section 2);
(b) lays down essential requirements for the concerned rolling stock domain and for its interfaces vis-à-vis
other subsystems (Section 3);
(c) establishes the functional and technical specifications to be met by the subsystem and its interfaces vis-
à-vis other subsystems (Section 4);
(d) determines the interoperability constituents and interfaces which must be covered by European spec
ifications, including European standards, which are necessary to achieve interoperability within the
trans-European conventional rail system (Section 5);
(e) states, in each case under consideration, which procedures are to be used in order to assess the
conformity or the suitability for use of the interoperability constituents, on the one hand, or the
‘EC’ verification of the subsystems, on the other hand (Section 6);
(f) indicates the strategy for implementing this TSI (Section 7);
(g) indicates for the staff concerned, the professional qualifications and health and safety conditions at
work required for the operation and maintenance of the subsystem, as well as for the implementation
of this TSI (Section 4).
In accordance with Article 5(5) of Directive 2008/57/EC, provision may be made for specific cases for each
TSI; such provisions are indicated in Section 7.
1.4. Referenced
documents
— Conventional rail ‘Locomotives and passenger rolling stock’ TSI (CR LOC & PAS TSI): present
document.
Legislative measures in force:
— Directive 2008/57/EC.
— Conventional Rail Control, command and signalling TSI: Commission Decision 2006/679/EC ( 1 ),
amended by Commission Decisions 2006/860/EC
( 2 ), 2007/153/EC
( 3 ), 2008/386/EC
( 4 ),
2009/561/EC ( 5 ) and 2010/79/EC ( 6 ).
— High-speed RST TSI: Commission Decision 2008/232/EC ( 7 )
— Accessibility for people with reduced mobility (PRM) TSI: Commission Decision 2008/164/EC ( 8 ).
— Safety in railway tunnels (SRT) TSI: Commission Decision 2008/163/EC ( 9 ).
( 1 ) OJ L 284, 16.10.2006, p. 1.
( 2 ) OJ L 342, 7.12.2006, p. 1.
( 3 ) OJ L 67, 7.3.2007, p. 13.
( 4 ) OJ L 136, 24.5.2008, p. 11.
( 5 ) OJ L 194, 25.7.2009, p. 60.
( 6 ) OJ L 37, 10.2.2010, p. 74.
( 7 ) OJ L 84, 26.3.2008, p. 132.
( 8 ) OJ L 64, 7.3.2008, p. 72.
( 9 ) OJ L 64, 7.3.2008, p. 1.

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/17
— Conventional rail noise TSI: Commission Decision 2006/66/EC ( 1 ).
— Conventional rail freight wagons TSI (CR WAG TSI): Commission Decision 2006/861/EC ( 2 ), amended
by Commission Decision 2009/107/EC ( 3 ).
— Conventional rail traffic operation and management (OPE) TSI: Commission Decision 2006/920/EC ( 4 ),
amended by Decision 2009/107/EC.
— Common safety methods (CSM): Commission Regulation (EC) No 352/2009 ( 5 ).
Legislative measures under adoption process:
— Conventional rail infrastructure TSI (CR INF TSI).
— Conventional rail energy TSI (CR ENE TSI).
— Description of modules for conformity assessment.
— Revision of the operation TSI (Annexes P and T).
Legislative measures under development:
— Telematic application for passengers TSI (TAP-TSI).
2. ROLLING
STOCK
SUBSYSTEM
AND
FUNCTIONS
2.1. The
rolling
stock
subsystem
as
part
of
the
conventional
rail
system
The trans-European rail system comprises a high speed rail system and a conventional rail system.
According to Directive 2008/57/EC, the rolling stock subsystem of the trans-European high-speed rail
system includes trains designed to operate on the trans-European high speed rail network (HS TEN),
composed of lines either dedicated high-speed lines or lines upgraded for high speed (i.e. speed of the
order of 200 km/h or more) indicated as such in Annex 1 of Decision No 1692/96/EC of the European
Parliament and of the Council ( 6 ).
Note: The HS RST TSI Section 1.1 sets a speed threshold of 190 km/h for the rolling stock in its technical
scope.
According to Directive 2008/57/EC, the rolling stock subsystem of the trans European conventional rail
system includes all trains likely to travel on all or part of the conventional lines of the TEN; the maximum
operational speed of these trains is not specified.
The conventional rail system has been broken down into subsystems as defined in Annex II (section 1) to
of Directive 2008/57/EC and listed as follows.
Structural areas:
— infrastructure,
— energy,
— control-command and signalling,
— rolling stock.
Functional areas:
— traffic operation and management,
( 1 ) OJ L 37, 8.2.2006, p. 1.
( 2 ) OJ L 344, 8.12.2006, p. 1.
( 3 ) OJ L 45, 14.2.2009, p. 1.
( 4 ) OJ L 359, 18.12.2006, p. 1.
( 5 ) OJ L 108, 29.4.2009, p. 4.
( 6 ) OJ L 228, 9.9.1996, p. 1.

---

L 139/18
EN
Official Journal of the European Union
26.5.2011
— maintenance,
— telematics applications for passenger and freight services.
With the exception of maintenance, each subsystem is dealt with in specific TSI(s).
The rolling stock subsystem dealt with in this TSI (as defined in Section 1.1) has interfaces with all other
subsystems of the conventional rail system mentioned above; these interfaces are considered within the
frame of an integrated system, compliant with all relevant TSIs.
Further to the development of the second TSI group there are:
— two TSIs describing specific aspects of the railway system and concerning several subsystems, the
conventional rail rolling stock being one of them:
(a) safety in railway tunnels;
(b) accessibility for people with reduced mobility;
and
— two TSIs concerning the conventional rail rolling stock subsystem:
(c) noise;
(d) freight wagons.
The requirements concerning the rolling stock subsystem expressed in these four TSIs are not repeated in
this TSI.
2.2. Definitions
related
to
rolling
stock
For the purpose of this TSI, the following definitions apply:
Train formation:
— A ‘unit’ is the generic term used to name the rolling stock which is subject to the application of this
TSI, and therefore subject to a certificate of ‘EC’ verification.
A unit may be composed of several ‘vehicles’, as defined in Directive 2008/57/EC, Article 2(c);
considering the scope of this TSI, the use of the term ‘vehicle’ in this TSI is limited to the rolling
stock subsystem.
— A ‘train’ is an operational formation consisting of one or more units.
— A ‘passenger train’ is an operational formation accessible to passengers (a train composed of passenger
vehicles but not accessible to passengers is not considered as a passenger train).
— A ‘fixed formation’ is a train formation that can only be reconfigured within a workshop environment.
— A ‘predefined formation(s)’ is a train formation(s) of several units coupled together, which is defined at
design stage and can be reconfigured during operation.
— ‘Multiple operation’: where ‘multiple operation’ is required:
— trainsets are designed so that several of them (of the type under assessment) are capable of being
coupled together to operate as a single train controlled from 1 driver’s cab,
— locomotives are designed so that several of them (of the type under assessment) are capable of being
included in a single train controlled from 1 driver’s cab.
— ‘General operation’: a unit is designed for general operation when the unit is intended to be coupled
with other unit(s) in a train formation which is not defined at design stage.

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/19
Rolling stock:
A — Self-propelling thermal and/or electric trains:
A ‘trainset’ is a fixed formation that can operate as a train; it is by definition not intended to be recon
figured, except within a workshop environment. It is composed of only motored or of motored and non-
motored vehicles.
‘An electric and/or diesel multiple unit’ is a trainset in which all vehicles are capable of carrying passengers
or luggage/mail.
A ‘railcar’ is a vehicle that can operate autonomously and is capable of carrying passengers or luggage/mail.
B — Thermal or electric traction units:
A ‘locomotive’ is a traction vehicle (or combination of several vehicles) that is not intended to carry a
payload and has the ability to uncouple in normal operation from a train and to operate independently.
A ‘shunter’ is a traction unit designed for use only on shunting yards, stations and depots.
Traction in a train can also be provided by a powered vehicle with or without driving cab, which is not
intended to be uncoupled during normal operation. Such a vehicle is called a ‘power car’ in general or a
‘power head’ when located at one end of the trainset and fitted with a driving cab.
C — Passenger carriages and other related cars:
A ‘coach’ is a non-traction vehicle in a fixed or variable formation capable of carrying passengers (by
extension, requirements specified to apply to coaches in this TSI are deemed to apply also to restaurant
cars, sleeping cars, couchettes cars, etc.). A coach may be equipped with a driver’s cab; such a coach is then
named a ‘driving coach’.
A ‘van’ is a non-traction vehicle capable of carrying payload other than passengers, e.g. luggage or mail,
intended to be integrated into a fixed or variable formation which is intended to transport passengers. A
van may be fitted with a driver’s cab and as such is known as a ‘driving van’.
A ‘driving trailer’ is a non-traction vehicle equipped with a driving cab.
A ‘car carrier’ is a non-traction vehicle capable of carrying passenger motor cars without their passengers
and which is intended to be integrated in a passenger train.
A ‘fixed rake of coaches’ is a non-traction formation of several coaches ‘semi-permanently’ coupled
together, or which can be reconfigured only when it is out of service.
D — Mobile railway infrastructure construction and maintenance equipment (or on-track machines)
‘On track machines (OTMs)’ are vehicles specially designed for construction and maintenance of the track
and infrastructure. OTMs are used in different modes: working mode, transport mode as self-propelling
vehicle, transport mode as a hauled vehicle.
‘Infrastructure inspection vehicles’ utilised to monitor the condition of the infrastructure are considered as
OTMs as defined above.
2.3. Rolling
stock
in
the
scope
of
this
TSI
The scope of this TSI concerning rolling stock, classified according to the types of rolling stock defined in
Section 1.1, is detailed as follows:
A — Self-propelling thermal or/and electric trains:
This type includes any passenger train in fixed or pre-defined formation.
Thermal or electric traction equipment is installed in some vehicles of the train, and the train is fitted with
a driver’s cab.

---

L 139/20
EN
Official Journal of the European Union
26.5.2011
Exclusion from the scope:
Rolling stock designed to operate primarily on urban tramway or light rail networks and intended to carry
passengers in urban and suburban areas is not in the scope of this TSI in its version.
Railcars or electric and/or diesel multiple units intended to operate on explicitly identified local (suburban
or regional) networks which are not parts of TEN lines are not in the scope of this TSI in its current
version.
When these types of rolling stock are intended to operate over very short distances on the TEN lines, due
to the local configuration of the railway network, Articles 24 and 25 of Directive 2008/57/EC (referring to
national rules) are applicable.
B — Thermal or electric traction units:
This type includes traction vehicles that are not capable of carrying a payload, such as thermal or electric
locomotives or power heads.
The concerned traction vehicles are intended for freight or/and passenger transport.
Exclusion from the scope:
Shunters, which are as defined not intended to operate on the main lines of the TEN, are not in the scope
of this TSI in its current version.
When they intended to operate shunting movements (short distances) on the main lines of the TEN,
Articles 24 and 25 of Directive 2008/57/EC (referring to national rules) are applicable.
C — Passenger carriages and other related cars:
— Passenger carriages:
This type includes non-traction vehicles carrying passengers, and operated in a variable formation with
vehicles from the category ‘thermal or electric traction units’ defined above to provide the traction
function.
— Non-passenger carrying vehicles included in a passenger train:
— Non-traction vehicles included in passenger trains (e.g. luggage or postal vans, car carriers, vehicles
for service…) are in the scope of this TSI, by extension of the concept of passenger carriages.
Exclusion from the scope:
— Freight wagons are not in the scope of this TSI; they are covered by the ‘freight wagons’ TSI even
when they are included in a passenger train (the train composition is in this case an operational
issue).
— Vehicles intended to carry road motor vehicles, with persons onboard these road motor vehicles, are
not in the scope of this TSI.
D — Mobile railway infrastructure construction and maintenance equipment:
This type of rolling stock is in the scope of the TSI only when:
— it is running on its own rail wheels,
— it is designed to be detected by a track based train detection system for traffic management, and
— it is in transport (running) configuration on its own rail wheels, self-propelled or hauled.
Working configuration is outside the scope of this TSI.

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/21
3. ESSENTIAL
REQUIREMENTS
3.1. General
According to Article 4(1) of Directive 2008/57/EC, the trans-European conventional rail system, its
subsystems and its interoperability constituents shall fulfil the essential requirements set out in general
terms in Annex III of Directive 2008/57/EC.
In the scope of this TSI, compliance with the specifications described in Section 4 for the subsystems, or
Section 5 for the interoperability constituents and demonstrated by a positive result of the assessment
described in Section 6.1 for the conformity and/or suitability for use of the interoperability constituents or
Section 6.2 for the verification of the subsystems, ensures fulfilment of the relevant essential requirements
quoted in Section 3.2.
Nevertheless, if part of the essential requirements are covered by national rules because of open points
declared in the TSI or specific cases described in Section 7.3, the corresponding national rules shall include
the conformity assessment, which shall be carried out under the responsibility of the relevant Member
State.
3.2. Elements
of
the
rolling
stock
subsystem
corresponding
to
the
essential
requirements
Regarding the rolling stock subsystem, the following table indicates the essential requirements, as defined
and numbered in Annex III of Directive 2008/57/EC, that are met by the specifications set out in Section 4
of this TSI.
Rolling stock elements corresponding to essential requirements
Element of the rolling stock subsystem Ref.
clause Safety
Reliability-
Technical
availability
Health
Environmental
protection
compatibility
Inner coupling 4.2.2.2.2 1.1.3
2.4.1
End coupling 4.2.2.2.3 1.1.3
2.4.1
Rescue coupling 4.2.2.2.4 2.4.2 2.5.3
Staff access for coupling and uncoupling 4.2.2.2.5 1.1.5 2.5.1 2.5.3
Gangways 4.2.2.3 1.1.5
Strength of vehicle structure 4.2.2.4 1.1.3
2.4.1
Passive safety 4.2.2.5 2.4.1
Lifting and jacking 4.2.2.6 2.5.3
Fixing of devices to car body structure 4.2.2.7 1.1.3
Staff and freight access doors 4.2.2.8 1.1.5
2.4.1
Mechanical characteristics of glass 4.2.2.9 2.4.1
Load conditions and weighted mass 4.2.2.10 1.1.3
Gauge — Kinematic gauge 4.2.3.1 2.4.3
Axle load 4.2.3.2.1 2.4.3
Wheel load 4.2.3.2.2 1.1.3
Rolling stock parameters which influence CCS subsystem 4.2.3.3.1 1.1.1 2.4.3
2.3.2
Axle bearing condition monitoring 4.2.3.3.2 1.1.1 1.2
Safety against derailment running on twisted track 4.2.3.4.1 1.1.1
2.4.3
1.1.2

---

L 139/22
EN
Official Journal of the European Union
26.5.2011
Element of the rolling stock subsystem Ref.
clause Safety
Reliability-
Technical
availability
Health
Environmental
protection
compatibility
Running dynamic behaviour 4.2.3.4.2 1.1.1
2.4.3
1.1.2
Limit values for running safety 4.2.3.4.2.1 1.1.1
2.4.3
1.1.2
Track loading limit values 4.2.3.4.2.2 2.4.3
Equivalent conicity 4.2.3.4.3 1.1.1
2.4.3
1.1.2
Design values for new wheel profiles 4.2.3.4.3.1 1.1.1
2.4.3
1.1.2
In-service values of wheelset equivalent conicity 4.2.3.4.3.2 1.1.2 1.2 2.4.3
Structural design of bogie frame 4.2.3.5.1 1.1.1
1.1.2
Mechanical and geometrical characteristics of wheelsets 4.2.3.5.2.1 1.1.1
2.4.3
1.1.2
Mechanical and geometrical characteristics of wheels 4.2.3.5.2.2 1.1.1
1.1.2
Variable gauge wheelsets 4.2.3.5.2.3 1.1.1
1.1.2
Minimum curve radius 4.2.3.6 1.1.1
2.4.3
1.1.2
Life guards 4.2.3.7 1.1.1
Braking — Functional requirements 4.2.4.2.1 1.1.1 2.4.2 1.5
2.4.1
Braking — Safety requirements 4.2.4.2.2 1.1.1 1.2
2.4.2
Type of brake system 4.2.4.3 2.4.3
Emergency braking command 4.2.4.4.1 2.4.1 2.4.3
Service braking command 4.2.4.4.2 2.4.3
Direct braking command 4.2.4.4.3 2.4.3
Dynamic braking command 4.2.4.4.4 1.1.3
Parking braking command 4.2.4.4.5 2.4.3
Braking performance -General requirements 4.2.4.5.1 1.1.1 2.4.2 1.5
2.4.1
Emergency braking 4.2.4.5.2 2.4.1 2.4.3
Service braking 4.2.4.5.3 2.4.3
Calculations related to thermal capacity 4.2.4.5.4 2.4.1 2.4.3
Parking brake 4.2.4.5.5 2.4.1 2.4.3
Limit of wheel rail adhesion profile 4.2.4.6.1 2.4.1 1.2
2.4.2
Wheel slide protection system 4.2.4.6.2 2.4.1 1.2
2.4.2

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/23
Element of the rolling stock subsystem Ref.
clause Safety
Reliability-
Technical
availability
Health
Environmental
protection
compatibility
Dynamic brake — Braking systems linked to traction
4.2.4.7 1.2
system
2.4.2
Braking system independent of adhesion conditions —
4.2.4.8.1. 1.2
General
2.4.2
Magnetic track brake 4.2.4.8.2. 2.4.3
Eddy current track brake 4.2.4.8.3 2.4.3
Brake state and fault indication 4.2.4.9 1.1.1 1.2
2.4.2
Brake requirements for rescue purposes 4.2.4.10 2.4.2
Sanitary systems 4.2.5.1 1.4.1
Public address system: audible communication system 4.2.5.2 2.4.1
Passenger alarm: functional requirements 4.2.5.3 2.4.1
Safety instructions to passengers — Signs 4.2.5.4 1.1.5
Communication devices for passengers 4.2.5.5 2.4.1
Exterior doors: access to and egress from Rolling stock 4.2.5.6 2.4.1
Exterior doors: system construction 4.2.5.7 1.1.3
2.4.1
inter-unit doors 4.2.5.8 1.1.5
Internal air quality 4.2.5.9 1.3.2
body side windows 4.2.5.10 1.1.5
Environmental conditions 4.2.6.1 2.4.2
Slipstream effects on passengers on platform 4.2.6.2.1 1.1.1 1.3.1
Slipstream effects on workers at the track side 4.2.6.2.2 1.1.1 1.3.1
Head pressure pulse 4.2.6.2.3 2.4.3
Maximum pressure variations in tunnels 4.2.6.2.4 2.4.3
Cross wind 4.2.6.2.5 1.1.1
Head lights 4.2.7.1.1 2.4.3
Marker lights 4.2.7.1.2 1.1.1 2.4.3
Tail lights 4.2.7.1.3 1.1.1 2.4.3
Lamp controls 4.2.7.1.4 2.4.3
Horn — General 4.2.7.2.1 1.1.1 2.4.3
2.6.3
Warning horn sound pressure levels 4.2.7.2.2 1.1.1 1.3.1
Protection 4.2.7.2.3 2.4.3
Horn control 4.2.7.2.4 1.1.1 2.4.3
Traction performance 4.2.8.1 2.4.3
2.6.3

---

L 139/24
EN
Official Journal of the European Union
26.5.2011
Element of the rolling stock subsystem Ref.
clause Safety
Reliability-
Technical
availability
Health
Environmental
protection
compatibility
Power supply 4.2.8.2
1.5
4.2.8.2.1 to
2.4.3
4.2.8.2.9
2.2.3
Electrical protection of the train 4.2.8.2.10 2.4.1
Diesel and other thermal traction system 4.2.8.3 2.4.1 1.4.1
Protection against electrical hazards 4.2.8.4 2.4.1
Driver’s cab — General 4.2.9.1.1
—
—
—
—
—
Access and egress 4.2.9.1.2 1.1.5 2.4.3
External visibility 4.2.9.1.3 1.1.1 2.4.3
Interior layout 4.2.9.1.4 1.1.5
Driver’s seat 4.2.9.1.5 1.3.1
Driver’s desk- Ergonomics 4.2.9.1.6 1.1.5 1.3.1
Climate control and air quality 4.2.9.1.7 1.3.1
Internal lighting 4.2.9.1.8 2.6.3
Windscreen — Mechanical characteristics 4.2.9.2.1 2.4.1
Windscreen — Optical characteristics 4.2.9.2.2 2.4.3
Windscreen — Equipment 4.2.9.2.3 2.4.3
Driver’s activity control function 4.2.9.3.1 1.1.1 2.6.3
Speed indication 4.2.9.3.2 1.1.5
Driver display unit and screens 4.2.9.3.3 1.1.5
Controls and indicators 4.2.9.3.4 1.1.5
Labelling 4.2.9.3.5 2.6.3
Remote control function from ground 4.2.9.3.6 1.1.1
Onboard tools and portable equipment 4.2.9.4 2.4.1 2.4.3
2.6.3
Storage facility for staff personal effects 4.2.9.5
—
—
—
—
—
Recording device 4.2.9.6 2.4.4
Fire safety — Material requirements 4.2.10.2 1.1.4 1.3.2 1.4.2
Specific measures for flammable liquids 4.2.10.3 1.1.4
Passenger evacuation 4.2.10.4 2.4.1
Fire barriers 4.2.10.5 1.1.4
Train exterior cleaning 4.2.11.2 1.5
Toilet discharge system 4.2.11.3 1.5
Water refilling equipment 4.2.11.4 1.3.1
Interface for water refilling 4.2.11.5 1.5
Special requirements for stabling of trains 4.2.11.6 1.5

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/25
Element of the rolling stock subsystem Ref.
clause Safety
Reliability-
Technical
availability
Health
Environmental
protection
compatibility
Refuelling equipment 4.2.11.7 1.5
General documentation 4.2.12.2 1.5
Documentation related to maintenance 4.2.12.3 1.1.1 2.5.1
2.5.2
2.6.1
2.6.2
Operating documentation 4.2.12.4 1.1.1 2.4.2
2.6.1
2.6.2
Lifting diagram and instructions 4.2.12.5 2.5.3
Rescue related descriptions 4.2.12.6 2.4.2 2.5.3
Note: Only clauses of the Section 4.2 which contain requirements are listed.
3.3. Essential
requirements
not
covered
by
this
TSI
Essential requirements classified as ‘general requirements’ or ‘specific to other subsystems’ in the Annex III
of Directive 2008/57/EC have for some of them an impact on; the rolling stock subsystem; those that are
not covered, or are covered with limitations within the scope of this TSI are identified below.
3.3.1. General
requirements,
requirements
related
to
maintenance
and
operation
The numbering of the paragraphs and the essential requirements hereunder are those set out in Annex III
of Directive 2008/57/EC.
The essential requirements that are not covered within the scope of this TSI are the following:
1.4. Environmental
protection
1.4.1. ‘The environmental impact of establishment and operation of the rail system must be assessed and
taken into account at the design stage of the system in accordance with the Community provisions
in force.’
This essential requirement is covered by the relevant European provisions in force.
1.4.3. ‘The rolling stock and energy-supply systems must be designed and manufactured in such a way as
to be electromagnetically compatible with the installations, equipment and public or private
networks with which they might interfere.’
This essential requirement is covered by the relevant European provisions in force.
1.4.4. ‘Operation of the rail system must respect existing regulations on noise pollution.’
This essential requirement is covered by the noise TSI in force.
1.4.5. ‘Operation of the rail system must not give rise to an inadmissible level of ground vibrations for the
activities and areas close to the infrastructure and in a normal state of maintenance.’
This essential requirement is covered by the CR Infrastructure TSI (open point in the current
version).
2.5. Maintenance
These essential requirements are relevant within the scope of this TSI according to Section 3.2 of
this TSI only for the technical maintenance documentation related to the rolling stock subsystem;
they are not in the scope of this TSI regarding maintenance installations.
2.6. Operation
These essential requirements are relevant within the scope of this TSI according to Section 3.2 of
this TSI for the operation documentation related to the rolling stock subsystem (essential
requirements 2.6.1 and 2.6.2), and for technical compatibility of the rolling stock with operating
rules (essential requirements 2.6.3).

---

L 139/26
EN
Official Journal of the European Union
26.5.2011
3.3.2. Requirements
specific
to
other
subsystems
Requirements on the relevant other subsystems are necessary to fulfil these essential requirements for the
whole railway system.
The requirements on the rolling stock subsystem which contribute to the fulfilment of these essential
requirements are mentioned in the Section 3.2 of this TSI, and are those set out in Sections 2.2.3 and 2.3.2
of Annex III to Directive 2008/57/EC.
Other essential requirements are not covered within the scope of this TSI.
4. CHARACTERISATION
OF
THE
ROLLING
STOCK
SUBSYSTEM
4.1. Introduction
4.1.1. General
The trans-European conventional rail system, to which Directive 2008/57/EC applies and of which the
rolling stock subsystem is a part, is an integrated system whose consistency shall be verified. This
consistency shall be checked in particular with regard to the specifications of the rolling stock subsystem,
its interfaces in relation to the other subsystems of the Conventional Rail system in which it is integrated,
as well as the operating and maintenance rules.
The basic parameters of the rolling stock subsystem are defined in the present Section 4 of this TSI.
Except where this is strictly necessary for the interoperability of the trans-European conventional rail
network, the functional and technical specifications of the subsystem and its interfaces described in
Sections 4.2 and 4.3, do not impose the use of specific technologies or technical solutions.
Innovative solutions, which do not fulfil the requirements specified in this TSI and/or which are not
assessable as stated in this TSI, require new specifications and/or new assessment methods. In order to
allow technological innovation, these specifications and assessment methods shall be developed by the
process ‘innovative solution’ described in Section 6.
Characteristics that need to be listed in the ‘European register of authorised types of vehicles’ are identified
in Section 4.8 of this TSI.
4.1.2.
Description of the rolling stock subject to the application of this TSI
Rolling stock subject to the application of this TSI (designated as a unit in the context of this TSI) shall be
described in the certificate of ‘EC’ verification, using one of the following characteristics:
— Trainset in fixed formation and, when required, predefined formation(s) of several trainsets of the type
under assessment for multiple operation.
— Single vehicle or fixed rakes of vehicles intended for predefined formation(s)
— Single vehicle or fixed rakes of vehicles intended for general operation and when required, predefined
formation(s) of several vehicles (locomotives) of the type under assessment for multiple operation.
Note: Multiple operation of the unit under assessment with other types of rolling stock in not in the scope
of this TSI.
Definitions related to train formation and units are given in Section 2.2 of this TSI.
When a unit intended for use in fixed or predefined formation(s) is assessed, the formations for which such
assessment is valid shall be defined by the party asking for assessment, and stated in the certificate of ‘EC’
verification. The definition of each formation shall include the type designation of each vehicle, the number
of vehicles and their arrangement in the formation. Details are given in Section 6.2.
Some characteristics or some assessments of a unit intended to be used in general operation, will require
defined limits regarding the train formations. These limits are laid down in Section 4.2 and in clause 6.2.6.
4.1.3.
Main categorisation of the rolling stock for application of TSI requirements
A rolling stock technical categorisation system is used in the following clauses of this TSI to define relevant
requirements applicable to a unit.

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/27
The technical category(ies) relevant for the unit subject to the application of this TSI shall be identified by
the party asking for assessment. This categorisation shall be used by the notified body in charge of the
assessment, in order to assess the applicable requirements from this TSI, and shall be stated in the
certificate of ‘EC’ verification.
The technical categories of rolling stock are the following:
— Unit designed to carry passengers.
— Unit designed to carry passenger-related load (luggage, cars, etc.).
— Unit fitted with a driver’s cab.
— Unit fitted with traction equipment.
— Electric unit, defined as a unit supplied with electric energy by an electrification system specified in the
CR energy TSI.
— Freight locomotive: Unit designed to haul freight wagons.
— Passenger locomotive: Unit designed to haul passenger carriages.
— Track construction and maintenance equipment (OTMs).
A unit can fall into one or several of the categories above.
Unless stated otherwise in the clauses of the Section 4.2, requirements specified in this TSI apply to all
technical categories of rolling stock defined above.
The unit operational configuration shall also be considered when it is assessed; a distinction shall be made
between:
— a unit that can be operated as a train,
— a unit that cannot be operated alone, and that has to be coupled with other unit(s) to be operated as a
train (see also clauses 4.1.2, 6.2.6 and 6.2.7).
4.1.4. Categorisation
of
the
rolling
stock
for
fire
safety
In respect of fire safety requirements, three categories of rolling stock are defined and specified in the clause
4.2.10 of this TSI.
In line with the HS RST TSI and SRT TSI, all rolling stock in the scope of this TSI shall be classified into (at
least) one of the categories:
— Category A fire safety,
— Category B fire safety,
— Freight locomotive and OTM.
4.2. Functional
and
technical
specification
of
the
subsystem
4.2.1. General
4.2.1.1. B
r
e
a
k
d
o
w
n
In light of the essential requirements in Section 3, the functional and technical specifications of the rolling
stock subsystem are grouped and sorted out in the following clauses of this section:
— Structures and mechanical parts
— Track interaction and gauging
— Braking
— Passenger related items

---

L 139/28
EN
Official Journal of the European Union
26.5.2011
— Environmental conditions
— External lights and audible and visible warning devices
— Traction and electrical equipment
— Driver’s cab and driver-machine interface
— Fire safety and evacuation
— Servicing
— Documentation for operation and maintenance
For particular technical aspects, the functional and technical specification makes an explicit reference to a
clause of an EN standard or other technical document, as allowed by Article 5(8) of Directive 2008/57/EC;
these references are listed in the Annex J of this TSI.
Information needed on board for the train staff to be aware of the operational state of the train (normal
state, equipment out of order, degraded situation …) are described in the clause dealing with the relevant
function, and in clause 4.2.12 ‘documentation requested for the operation and maintenance’.
4.2.1.2.
O p e n p o i n t s
When, for a particular technical aspect, the functional and technical specification necessary to meet the
essential requirements has not been developed, and therefore is not included in this TSI, this aspect is
identified as an open point in the relevant clause; Annex I of this TSI lists all open points, as required in
Article 5(6) of Directive 2008/57/EC.
The Annex I mentions also if the open points relate to technical compatibility with the network; for this
purpose, the Annex I is split in 3 parts:
— General open points that apply to a whole network.
— Open points that relate to technical compatibility between the vehicle and the network.
— Open points that do not relate to technical compatibility between the vehicle and the network.
As required in Article 17(3) of Directive 2008/57/EC, open points shall be addressed by the application of
national technical rules.
4.2.1.3.
S a f e t y a s p e c t s
The functions that contribute to meet the essential requirements ‘safety’ are identified in Section 3.2 of this
TSI.
Most of the safety requirements related to these functions are covered by the technical specifications
expressed in Section 4.2 (e.g. ‘passive safety’, ‘wheels’ …).
For the following safety related functions, the technical specifications need to be completed by
requirements expressed in terms of safety requirement, for which the demonstration of compliance may
use the principles described in the CSM on RA (similarity with reference system(s), application of codes of
practice, probabilistic approach):
— Dynamic behaviour (when active control is utilised), as specified in clause 4.2.3.4.2.
— Emergency braking performance (including traction cut off), as specified in clause 4.2.4.2, clause 4.2.4.7
and clause 4.2.4.8.1; the safety requirements are specified in clause 4.2.4.2.2.
— Parking braking, as specified in clause 4.2.4.2, clause 4.2.4.4.5 and clause 4.2.4.5.5; the safety
requirements are specified in clause 4.2.4.2.2.
— Brake state and fault indication, as specified in clause 4.2.4.9.
— Passenger alarm, as specified in clause 4.2.5.3.

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/29
— Control of passenger exterior doors, as specified in clause 4.2.5.6.
— Electric power supply cut off, as specified in clause 4.2.8.2.10.
— Driver’s activity control, as specified in clause 4.2.9.3.1.
— Fire barriers (other than full cross section partitions), as specified in clause 4.2.10.5.
Where these functions, identified as safety related, have their safety aspects not sufficiently covered, or no
safety specified, this is identified as an open point in the corresponding clause specifying the function.
Software which is used to fulfil safety related functions shall be developed and assessed according to a
methodology adequate for safety related software.
This applies to software which has an impact on functions identified as safety related in the Section 4.2 of
this TSI.
4.2.2. Structure
and
mechanical
parts
4.2.2.1. G
e
n
e
r
a
l
This part addresses requirements relating to the design of vehicle structural body (strength of vehicle
structure) and of the mechanical links (mechanical interfaces) between vehicles or between units.
Most of these requirements aim at ensuring the train’s mechanical integrity in operation and rescue
operation as well as protecting passenger and staff compartments in the event of collision or derailment.
4.2.2.2.
M e c h a n i c a l i n t e r f a c e s
4.2.2.2.1.
G e n e r a l a n d d e f i n i t i o n s
In order to form a train (as defined in Section 2.2) vehicles are coupled together in a way that enables them
to be operated together. The coupling is the mechanical interface that enables this. There are several types
of couplings:
— ‘Inner’ coupling (also called ‘intermediate’ coupling) is the coupling device between vehicles in order to
form a unit composed of several vehicles (e.g. a fixed rake of coaches or a trainset).
— End coupling (‘external’ coupling) of units is the coupling device used to couple together two (or
several) units to form a train. The fitting of end coupling at the end of units is not mandatory.
Where there is no coupling at any end of a unit, a device to allow a rescue coupling shall be
provided at such end of the unit.
An end coupling can be ‘automatic’, ‘semi-automatic’ or ‘manual’.
In the context of this TSI, a ‘Manual’ coupling is an end coupling system which requires (one or several)
person(s) to stand between the units to be coupled or uncoupled for the mechanical coupling of these
units.
— Rescue coupling is the coupling device that enables a unit to be rescued by a recovery power unit
equipped with a ‘standard’ manual coupling as per clause 4.2.2.2.3 where the unit to be rescued is
equipped with a different coupling system or is not equipped with any coupling system.
4.2.2.2.2.
I n n e r c o u p l i n g
Inner couplings between the different vehicles of a unit shall incorporate a resilient system capable of
withstanding the forces due to the intended operating conditions.
Where the inner coupling system between vehicles has a lower longitudinal strength than the end
coupling(s) of the unit, provisions shall be made to rescue the unit in case of breakage of any such
inner coupling; these provisions shall be described in the documentation required in clause 4.2.12.6.
Articulated units: The joint between two vehicles sharing the same running gear, shall comply with the
requirements of Sections 6.5.3 and 6.7.5 of the EN12663-1:2010.

---

L 139/30
EN
Official Journal of the European Union
26.5.2011
4.2.2.2.3. E
n
d
c
o
u
p
l
i
n
g
(a) End coupling — General
Where an end coupling is provided at any end of a unit, the following requirements apply to all types of
end coupling (automatic, semi-automatic or manual):
— End couplings shall incorporate a resilient coupling system, capable of withstanding the forces due to
the intended operational and rescue conditions.
— The type of mechanical coupling together with its nominal maximum design values of tensile and
compressive forces shall be recorded in the rolling stock register defined in clause 4.8 of this TSI.
There is no further requirement for automatic and semi-automatic coupling systems in this TSI.
(b) ‘Manual’ coupling system
The following provisions apply specifically to units fitted with a ‘manual’ coupling system:
— The coupling system shall be designed so that no human presence between the units to be coupled/
uncoupled is required whilst either one is moving.
— Coaches with manual coupling systems shall be fitted with a buffer, draw gear and screw coupling
system complying with the requirements of the parts of EN15551:2009 and EN15566:2009 related to
passenger coaches; Units other than coaches with manual coupling systems shall be fitted with a buffer,
draw gear and screw coupling system complying with the relevant parts of EN15551:2009 and
EN15566:2009 respectively.
In all cases, the buffers and the screw coupling shall be installed according to clauses A.1 to A.3 of Annex
A.
On all units designed to operate solely on the standard 1 435 mm gauge network, and equipped with
manual coupling and UIC pneumatic brake, the following requirements apply:
— The dimensions and layout of brake pipes and hoses, couplings and cocks shall meet the requirements
stated in the Annex I of the CR WAG TSI. The longitudinal and vertical location of brake pipes and
cocks from the buffer plate shall comply with the corresponding requirements set out in UIC leaflet
541-1:Nov 2003 Annex B2 figure 16b or 16c.
Note: They will be subject of an EN standard currently under drafting process.
— The lateral location of brake pipes and cocks is permitted to comply with the requirements of UIC
648:Sep 2001.
(c) Manual coupling system — Compatibility between units designed to be operated on networks with
different track gauges
Units designed for operation on networks with several track gauges (e.g. 1 435 mm and 1 520/1 524 mm,
or 1 435 mm and 1 668 mm), equipped with ‘Manual’ coupling and UIC pneumatic brake system, shall be
compatible with both:
— The interface requirements in the clause 4.2.2.2.3 ‘End coupling’ for 1 435 mm networks, and
— The associated specific case for the ‘other than 1 435 mm’ network as depicted in clause 7.3 of this TSI.
4.2.2.2.4.
R e s c u e c o u p l i n g
At the ends of units not equipped with any end coupling feature, or equipped with a coupling system
which is not compatible with the manual coupling system as per clause 4.2.2.2.3 of this TSI, provisions
shall be made to enable the recovery of the line in case of breakdown by hauling or propelling the unit to
be rescued:
— Where the unit to be rescued is fitted with an end coupling: by means of a power unit equipped with
the same type of end coupling system, and
— By means of a recovery unit i.e. a power unit featuring at each of its ends intended to be used for
rescue purposes:
— a manual coupling system and pneumatic brake compliant to 4.2.2.2.3 above,

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/31
— lateral location of brake pipes and cocks according to UIC 648:Sep 2001,
— a free space of 395 mm above the centre line of the hook to allow the fitting of the rescue adaptor
as described below.
This is achieved either by means of a permanently installed compatible coupling system or through a
rescue coupler (also called rescue adaptor).
In such a case, the unit to be assessed shall be designed so that it is possible to carry the rescue coupler
onboard.
The rescue coupler shall:
— be designed to allow the rescue at a speed of at least 30km/h on railway lines which comply with the
CR INF TSI,
— be secured after mounting onto the recovery unit in a way that prevents it coming off during the rescue
operation,
— withstand the forces due to the intended rescuing conditions,
— be designed such that it does not require any human presence between the recovery unit and the unit
to be rescued whilst either one is moving,
— neither the rescue coupler nor any braking hose shall limit the lateral movement of the hook when
fitted onto the recovery unit.
The brake interface is covered by the requirements of clause 4.2.4.10 of this TSI.
4.2.2.2.5.
S t a f f a c c e s s f o r c o u p l i n g a n d u n c o u p l i n g
Units shall be designed so that staff are not exposed to undue risk during coupling and uncoupling, or
rescue operations.
To comply with this requirement, units fitted with manual coupling systems as per clause 4.2.2.2.3 shall
comply with the following requirements (the ‘Bern rectangle’):
— The required spaces shown in figure A2 of Annex A shall be free of fixed parts. For this requirement
the coupling gear components are in the central position laterally.
Connecting cables and flexible hoses as well as elastic deformable parts of gangways may be inside this
space. There shall be no devices under the buffers that hinder the access to the space.
— Where a combined automatic and screw coupler is fitted it is permissible for the auto coupler head to
infringe the Berne rectangle on the left hand side (as viewed on figure A2) when it is stowed and the
screw coupler is in use.
— There shall be a handrail under each buffer. The handrails shall withstand a force of 1,5 kN.
4.2.2.3.
G a n g w a y s
Where a gangway is provided as a means for passengers to circulate from one coach or one trainset to
another, it shall not expose passengers to undue risk.
Where operation with the gangway not being connected is foreseen, it shall be possible to prevent access
by passengers to the gangway.
Requirements related to the gangway door when the gangway is not in use are specified in clause 4.2.5.8
‘Passenger related items — Inter-unit doors’.
Additional requirements are expressed in the PRM TSI (clause 4.2.2.7 of PRM TSI ‘Clearways’).
These requirements do not apply to the end of vehicles where this area is not intended for regular use by
passengers.

---

L 139/32
EN
Official Journal of the European Union
26.5.2011
4.2.2.4.
S t r e n g t h o f v e h i c l e s t r u c t u r e
This clause applies to all units.
For mobile railway infrastructure construction and maintenance equipment (OTMs), alternative
requirements to those expressed in this clause for static load, category and acceleration are set out in
Annex C, clause C.1.
The static and dynamic strength (fatigue) of vehicle bodies is relevant to ensure the safety required for the
occupants and the structural integrity of the vehicles in train and in shunting operations.
Therefore, the structure of each vehicle shall comply with the requirements of EN 12663-1:2010 Structural
requirements of railway vehicle bodies — Part 1, Locomotives and passenger rolling stock (and alternative
method for freight wagons). The rolling stock categories to be taken into account shall correspond to
category L for locomotives and power units and categories PI or PII for all other types of vehicle within the
scope of this TSI, as defined in Section 5.2 of EN 12663-1:2010.
In particular, proof of the capacity of the vehicle body to resist lasting deformations and fractures may be
demonstrated by calculations or by testing, according to the conditions set up in the clause 9.2.3.1 of EN
12663-1:2010.
The load conditions to be considered shall be in accordance with clause 4.2.2.10 of this TSI.
The assumptions for aerodynamic loading shall be those described in clause 4.2.6.2.3 of this TSI.
Joining techniques are covered by the above requirements. A verification procedure shall exist to ensure at
the production phase that no defect may decrease the mechanical characteristics of the structure.
4.2.2.5.
P a s s i v e s a f e t y
Except for units not intended to carry passengers or staff during operation and except for OTMs, this
requirement is applicable to all units.
In addition, units which cannot operate up to the collision speeds specified under any of the collision
scenarios below are exempted from the provisions related to that collision scenario.
Passive safety is aimed at complementing active safety when all other measures have failed.
For this purpose, the mechanical structure of vehicles shall provide protection of the occupants in the event
of a collision by providing means of:
— limiting deceleration,
— maintaining survival space and structural integrity of the occupied areas,
— reducing the risk of overriding,
— reducing the risk of derailment,
— limiting the consequences of hitting a track obstruction.
To meet these functional requirements, units shall comply with the detailed requirements specified in the
standard EN15227:2008 related to crashworthiness design category C-I (as per table 1 of EN15227:2008
Section 4), unless specified otherwise below.
The following four reference collision scenarios shall be considered:
— Scenario 1: A front end impact between two identical units,
— Scenario 2: A front end impact with a freight wagon,
— Scenario 3: An impact of the unit with a large road vehicle on a level crossing,
— Scenario 4: An impact of the unit into a low obstacle (e.g. car on a level crossing, animal, rock etc.).

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/33
These scenarios are described in table 2 of Section 5 of EN15227:2008.
Within the scope of the present TSI, table 2 application rules are completed by the following:
— The application of requirements related to scenarios 1 and 2 to heavy haul locomotives used only for
freight operations and fitted with centre couplers conforming to the Willison (e.g. SA3) or Janney (AAR
standard) principle which are intended to operate on the CR TEN lines is an open point.
— The assessment of conformity of locomotives with central cabs with the requirements related to
scenario 3 is an open point.
The present TSI specifies crashworthiness requirements applicable within its scope; therefore, Annex A of
EN 15227:2008 shall not apply. The requirements of Section 6 of EN15227:2008 shall be applied in
relation to the above given reference collision scenarios.
To limit the consequences of hitting a track obstruction, the leading ends of locomotives, power heads,
driving coaches and trainsets shall be equipped with an obstacle deflector. The requirements with which
obstacle deflectors shall comply are defined in EN15227:2008 §5 table 3 and Section 6.5.
4.2.2.6.
L i f t i n g a n d j a c k i n g
Except for OTMs (mobile railway infrastructure construction and maintenance equipment), this clause
applies to all units.
Provisions concerning the lifting and jacking of OTMs are specified in Annex C, clause C.2.
It shall be possible to safely lift or jack each vehicle composing the unit, for recovery purposes (following
derailment or other accident or incident), and for maintenance purposes.
It shall also be possible to lift or jack any end of the vehicle (including its running gear) with the other end
resting on the remaining running gear(s).
To this purpose, designated and marked lifting/jacking points shall be provided.
The geometry and location of the lifting points shall be compliant with Annex B.
Marking of lifting points shall be made by signs compliant with Annex B.
The structure shall resist to the loads specified in EN 12663-1:2010 (section 6.3.2 and 6.3.3).
In particular, proof of the capacity of the vehicle body to resist lasting deformations and fractures may be
demonstrated by calculations or by testing, according to the conditions set up in clause 9.2.3.1 of EN
12663-1:2010.
4.2.2.7.
F i x i n g o f d e v i c e s t o c a r b o d y s t r u c t u r e
Except for OTMs (mobile railway infrastructure construction and maintenance equipment), this clause
applies to all units.
Provisions concerning the structural strength of OTMs are specified in Annex C, clause C.1.
To reduce the consequences of an accident, fixed devices including those inside the passenger areas, shall be
attached to the car body structure in a way that prevents these fixed devices becoming loose and presenting
a risk of passenger injuries or lead to a derailment. To this aim, attachments of these devices shall be
designed according to Section 6.5.2 of the EN 12663-1:2010 for categories defined in clause 4.2.2.4 above.
4.2.2.8.
S t a f f a n d f r e i g h t a c c e s s d o o r s
The doors for use of passengers are covered by the clause 4.2.5 of this TSI: ‘Passenger related items’. Cab
doors are addressed in clause 4.2.9 of this TSI.
This clause addresses doors for freight use and for use of train crew other than cab doors.
Vehicles fitted with a compartment dedicated to train crew or freight shall be equipped with a device to
close and lock the doors. The doors shall remain closed and locked until they are intentionally released.

---

L 139/34
EN
Official Journal of the European Union
26.5.2011
4.2.2.9.
M e c h a n i c a l c h a r a c t e r i s t i c s o f g l a s s ( o t h e r t h a n w i n d s c r e e n s )
Where glass is used in glazing (including mirrors), it shall be either laminated or toughened glass which is
in accordance with a relevant national or international standard with regard to the quality and area of use,
thereby minimising the risk to passenger and staff being injured by breaking glass.
4.2.2.10.
L o a d c o n d i t i o n s a n d w e i g h t e d m a s s
The following load conditions defined in clause 3.1 of the standard EN 15663:2009 shall be determined:
— Design mass under exceptional payload.
— Design mass under normal payload.
— Design mass in working order.
The hypothesis taken for arriving at the load conditions above shall be in line with the standard EN
15663:2009 (long distance train, other train, payload per m 2 in standing and service areas); they shall be
justified and documented in the general documentation described in clause 4.2.12.2.
For OTMs, different load conditions (minimum mass, maximum mass) may be used, in order to take into
account optional onboard equipment.
For each load condition defined above, the following information shall be provided in the technical
documentation described in clause 4.2.12:
— Total vehicle mass (for each vehicle of the unit).
— Mass per axle (for each axle).
— Mass per wheel(for each wheel).
The load condition ‘design mass in working order’ shall be measured by vehicle weighing. It is permissible
to derive the other load conditions by calculation.
Where a vehicle is declared as conformant to a type (in accordance with clauses 6.2.2.1 and 7.1.3), the
weighted total vehicle mass in the load condition ‘design mass in working order’ shall not exceed by more
than 3 % the declared total vehicle mass for that type which is reported in the type or design examination
certificate of ‘EC’ verification.
The design mass of the unit in working order, the design mass of the unit under normal payload and the
highest axle load of the individual axles for each one of the 3 load cases shall be recorded in the rolling
stock register defined in clause 4.8 of this TSI.
4.2.3. Track
interaction
and
gauging
4.2.3.1. G
a
u
g
i
n
g
The gauge is an interface between the unit (vehicle) and the infrastructure described by a common reference
contour and associated rules for the calculation. The gauge is a performance parameter specified in clause
4.2.2 of the CR INF TSI and depends on the category of line.
The kinematic reference contour with its associated rules describes the outer dimensions of the unit; it shall
be within one of the reference profiles GA, GB or GC (according to clause 4.2.2 of the CR INF TSI). The
assumed sway (or flexibility) coefficient for the gauge calculation shall be justified by calculation or
measurements as set out in EN 15273-2:2009.
For electric units, the pantograph gauge shall be verified by calculation according to clause A.3.12 of EN
15273-2:2009 to ensure that the pantograph envelope complies with the mechanical kinematic
pantograph gauge which in itself is determined according to Annex E of CR ENE TSI, and depends on
the choice made for the pantograph head geometry: the two permitted possibilities are defined in clause
4.2.8.2.9.2 of this TSI.
The voltage of the power supply is considered in the infrastructure gauge in order to ensure the proper
insulation distances between the pantograph and fixed installations.
The pantograph sway as specified in clause 4.2.14 of CR energy TSI and used for the mechanical kinematic
gauge calculation shall be justified by calculations or measurements as set out in EN 15273-2:2009.

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/35
The reference contour (i.e. gauge) that the unit complies with (GA, GB or GC) shall be recorded in the
rolling stock register defined in clause 4.8 of this TSI.
Any gauge, with a kinematic reference profile smaller than GC, may also be recorded in the register
together with the harmonised applicable gauge (GA, GB or GC), provided it is assessed using the
kinematic method.
4.2.3.2.
A x l e l o a d a n d w h e e l l o a d
4.2.3.2.1.
A x l e l o a d p a r a m e t e r
The axle load is an interface between the unit and the infrastructure. The axle load is a performance
parameter of the infrastructure specified in clause 4.2.2 of the CR INF TSI and depends on the Category of
Line. It has to be considered in combination with the axle spacing, with the train length and with the
maximum allowed speed for the unit on the considered line.
The following characteristics to be used as an interface to the infrastructure shall be part of the general
documentation produced when the unit is assessed, and described in clause 4.2.12.2:
— The mass per axle (for each axle) for the 3 load conditions (as defined and required to be part of the
documentation in clause 4.2.2.10).
— The position of the axles along the unit (axle spacing).
— The length of the unit.
— The maximum design speed (as required to be part of the documentation in clause 4.2.8.1.2).
Use of this information at operational level for compatibility check between rolling stock and infrastructure
(outside the scope of this TSI):
The axle load of each individual axle of the unit to be used as interface parameter to the infrastructure has
to be defined by the Railway Undertaking as required in clause 4.2.2.5 of the CR OPE TSI, considering the
expected load for the intended service (not defined when the unit is assessed). The axle load in load
condition ‘design mass under exceptional payload’ represents the maximum possible value of the axle
load mentioned above.
4.2.3.2.2. W
h
e
e
l
l
o
a
d
The ratio of wheel load difference per axle qj, shall be evaluated by wheel load measurement, considering
the load condition ‘design mass in working order’. Wheel load difference higher than 5 % of the axle load
are allowed only if demonstrated as acceptable by the test to prove safety against derailment on twisted
track specified in the clause 4.2.3.4.1 of this TSI.
4.2.3.3.
R o l l i n g s t o c k p a r a m e t e r s w h i c h i n f l u e n c e g r o u n d b a s e d s y s t e m s
4.2.3.3.1.
R o l l i n g s t o c k c h a r a c t e r i s t i c s f o r t
h
e c
o
m
p
a
t
i
b
i
l
i
t y w i t h t r a i n d e t e c t i o n
s y s t e m s
The set of rolling stock characteristics for compatibility with train detection target systems are given in
clauses 4.2.3.3.1.1, 4.2.3.3.1.2 and 4.2.3.3.1.3.
The set of characteristics the rolling stock is compatible with shall be recorded in the rolling stock register
as defined in clause 4.8 of this TSI.
4.2.3.3.1.1. ROLLING STOCK CHARACTERISTICS FOR COMPATIBILITY WITH TRAIN DETECTION SYSTEM BASED
ON TRACK CIRCUITS
— Vehicle geometry
— The maximum distance between 2 consecutive axles is specified in CR CCS TSI Annex A Appendix
1 clause 2.1.1.
— The maximum distance between buffer end and first axle is specified in CR CCS TSI Annex A
Appendix 1 clause 2.1.2 (distance b1 in figure 6).

---

L 139/36
EN
Official Journal of the European Union
26.5.2011
— Vehicle design
— The minimum axle load in all load conditions is specified in CR CCS TSI Annex A Appendix 1
clauses 3.1.1 and 3.1.2.
— The electrical resistance between the running surfaces of the opposite wheels of a wheelset is
specified in CR CCS TSI Annex A Appendix 1 clause 3.5.1 and the method to measure is
specified in the same Appendix clause 3.5.2.
— For electric units equipped with a pantograph and supplied with power supply 1 500 V DC or
3 000 V DC(see clause 4.2.8.2.1), the minimum impedance between pantograph and each wheel of
the train is specified in CR CCS TSI Annex A Appendix 1 clause 3.6.1
— Isolating emissions
— The limitations of use of sanding equipment are given in CR CCS TSI Annex A Appendix 1 clauses
4.1.1 and 4.1.2.
— The use of composite brake blocks is an open point in the CR CCS TSI.
— EMC
— The electromagnetic interference limit levels rising from traction currents are an open point in the
CR CCS TSI.
4.2.3.3.1.2. ROLLING
STOCK
CHARACTERISTICS
FOR
COMPATIBILITY
WITH
TRAIN
DETECTION
SYSTEM
BASED
ON AXLE COUNTERS ( 1 )
— Vehicle geometry
— The maximum distance between 2 consecutive axles is specified in CR CCS TSI Annex A Appendix
1 clause 2.1.1.
— The minimum distance between 2 consecutive axles of the train is specified in CR CCS TSI Annex A
Appendix 1 clause 2.1.3.
— At the end of a unit intended to be coupled, the minimum distance between end and first axle of
the unit is half of the value specified in CR CCS TSI Annex A Appendix 1 clause 2.1.3.
— The maximum distance between end and first axle is specified in CR CCS TSI Annex A Appendix 1
clause 2.1.2 (distance b1 in figure 6).
— The minimum distance between end axles of a unit is specified in CR CCS TSI Annex A Appendix 1
clause 2.1.4
— Wheel geometry
— Wheel geometry is specified in the clause 4.2.3.5.2.2 of the present TSI.
— The minimum wheel diameter (speed dependant) is specified in CR CCS TSI Annex A Appendix 1
clause 2.2.2.
— Vehicle design
— The metal-free space around wheels is an open point in the CR CCS TSI.
— The characteristics of the wheel material regarding magnetic field is specified in CR CCS TSI Annex
A Appendix 1 clause 3.4.1.
— EMC
— The electromagnetic interference limit levels rising from the use of eddy current or magnetic track
brakes are an open point in the CR CCS TSI.
( 1 ) Clauses 2 and 3 of Annex A Appendix 1 in Decision 2006/679/EC are numbered clauses 52006 and 6 in Decision 2006/860/EC
amending it.

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/37
4.2.3.3.1.3. ROLLING STOCK CHARACTERISTICS FOR COMPATIBILITY WITH TRAIN DETECTION SYSTEM BASED
ON LOOP EQUIPMENT
— Vehicle design
The metal-mass of vehicles is an open point in the CR CCS TSI.
4.2.3.3.2.
A x l e b e a r i n g c o n d i t i o n m o n i t o r i n g
The axle bearing condition monitoring shall be made possible.
This is permitted to be achieved either by onboard equipment or by using track side equipment.
The requirement for onboard equipment is an open point in this TSI.
In case of monitoring of axle bearing by trackside equipment, the rolling stock shall comply with the
following requirements:
— The zone visible to the trackside equipment on rolling stock shall be the area as defined in EN 15437-
1:2009 clauses 5.1 and 5.2.
— The range of working temperature of the axle bearing is an open point.
Note: See also clause 4.2.3.5.2.1 regarding axle boxes.
4.2.3.4.
R o l l i n g s t o c k d y n a m i c b e h a v i o u r
4.2.3.4.1.
S a f e t y a g a i n s t d e r a i l m e n t r u n n i n g o n t w i s t e d t r a c k
The unit (or vehicles composing the unit) shall be designed to ensure safe running on twisted track, taking
into account specifically the transition phase between canted and level track and cross level deviations. The
compliance with this requirement shall be verified by the procedure defined in clause 4.1 of EN
14363:2005.
For OTMs safety against derailment when running on track twists is permitted to be proved by an
approved calculation method. If this is not possible, tests according to the requirements of EN 14363:2005
shall be carried out.
For running on track twists the testing conditions according to EN 14363:2005, clause 4.1 apply for
machines with bogies as well as with individual wheel sets.
4.2.3.4.2.
R u n n i n g d y n a m i c b e h a v i o u r
(a) Introduction
This clause 4.2.3.4.2 is applicable to units designed for a speed higher than 60 km/h.
It is not applicable to OTMs (mobile railway infrastructure construction and maintenance equipment);
requirements for OTMs are set out in Annex C, clause C.3.
The dynamic behaviour of a vehicle has a strong influence on safety against derailment, running safety and
track loading. It is a safety related function, which is covered by the technical requirements of this clause;
when software is utilised, the safety level to be considered for developing the software is an open point.
(b) Requirements
In order to verify the running dynamic characteristics of a unit (running safety and track loading), the
process sets out in EN 14363:2005 clause 5 and in addition for tilting trains in EN 15686:2010 shall be
followed, with the amendments expressed below (in this clause and its sub clauses). The parameters
described in clauses 4.2.3.4.2.1 and 4.2.3.4.2.2 shall be assessed using criteria defined in EN 14363:2005.
As an alternative to performing on-track tests on two different rail inclinations, as set out in paragraph
5.4.4.4 in EN 14363:2005 it is permitted to perform tests on only one rail inclination if demonstrated that
the tests cover the range of contact conditions defined below:
— The parameter equivalent conicity tan γ e for tangent track and large radius curves shall be distributed so
that tan γ e = 0,2 ± 0,05 occurs in a range of the amplitude (y) of the wheelset’s lateral displacement
between +/- 2 and +/- 4 mm for a minimum of 50 % of track sections.

---

L 139/38
EN
Official Journal of the European Union
26.5.2011
— The instability criterion in EN14363:2005 shall be assessed for low-frequency body motions on at least
two track sections with equivalent conicities less than 0,05 (mean value over the track section).
— The instability criterion in EN14363:2005 shall be assessed on at least two track sections with
equivalent conicities in accordance with the following table 1:
Table 1
Conditions for contact conditions in relation to on-track testing
Maximum vehicle speed Equivalent
conicity
60 km/h < V ≤ 140 km/h
≥ 0,50
140 km/h < V ≤ 200 km/h
≥ 0,40
200 km/h < V ≤ 230 km/h
≥ 0,35
230 km/h < V ≤ 250 km/h
≥ 0,30
In addition to the requirements concerning the test report given in clause 5.6 of EN 14363:2005, the test
report shall include information on:
— The track quality on which the unit was tested on, recorded by the monitoring of a consistent set of
some of the parameters set out in EN 13848-1:2003/A1:2008, the selected set of parameters
depending on available measurement means.
— The equivalent conicity that the unit was tested for.
The test report shall be part of the documentation described in clause 4.2.12.
(c) Quality of the track for tests and on-track tests:
Tests conditions: EN14363 defines test conditions for on-track tests which have been agreed as a reference.
However these test conditions are not always achievable, due to constraints related to the zone where the
test is performed, in the following areas:
— Track geometric quality.
— Combinations of speed, curvature, cant deficiency (clause 5.4.2 of EN 14363).
Regarding the track geometric quality, the specification of a reference track for tests, including limits of the
track quality parameters which are defined in EN 13848-1, is an open point. Therefore, national rules apply
for the definition of these limits, which shall be expressed in consistency with EN 13848-1, in order to be
able to evaluate if a test already performed is acceptable.
4.2.3.4.2.1. LIMIT
VALUES
FOR
RUNNING
SAFETY
The limit values for running safety which the unit shall meet are specified in EN 14363:2005 clause
5.3.2.2, and additionally for tilting trains in EN 15686:2010, with the following modification of the
quotient of guiding force and wheel force (Y/Q):
When the quotient of guiding force and wheel force (Y/Q) limit is exceeded, it is allowed to recalculate the
Y/Q estimated maximum value according to the following process:
— create an alternative test zone made up of all track sections with 300 m ≤ R ≤ 500 m,
— for the statistical processing per section, use x i (97,5 %) instead of x i (99,85 %),
— for statistical processing per zone, replace k = 3 (when using one-dimensional method) or student
coefficient t (N-2; 99 %) (when using two-dimensional method) by student coefficient t (N-2; 95 %).
Both results (before and after recalculation) shall be recorded in the test report.

---

EN
26.5.2011 Official
Journal
of
the
European
Union L
139/39
4.2.3.4.2.2. TRACK
LOADING
LIMIT
VALUES
Except for the quasi static guiding force Y qst , the limit values for track loading which the unit shall meet
when testing with the normal method, are specified in EN 14363:2005 clause 5.3.2.3.
The quasi static guiding force Y qst limits are specified below.
The quasi-static guiding force Y qst limit value shall be evaluated for curve radii 250 ≤ R < 400 m.
The limit value for unrestricted operation of the rolling stock on the TEN network (as defined in TSIs) shall
be: (Y qst )lim = (30 + 10500/R m ) kN.
Where: R m = mean radius of the track sections retained for the evaluation (in metres).
When this limit value is exceeded due to high friction conditions, it is permitted to recalculate the
estimated value of Y qst on the zone after replacing the individual (Y qst ) i values on the track sections ‘i’
where (Y/Q) ir (mean value of Y/Q ratio on the inner rail over the section) exceeds 0,40 by: (Y qst ) i -
50[(Y/Q) ir - 0,4].The values of the Yqst, Qqst and mean curve radius (before and after recalculation)
shall be recorded in the test report.
In case the Yqst value exceeds the limit value expressed above, the operational performance of the rolling
stock (e.g. maximum speed) may be limited by the infrastructure, considering track characteristics (e.g.
curve radius, cant, rail height).
Note: The limit values specified in EN 14363:2005 are applicable for axle loads in the range of those
mentioned in the clause 4.2.2 of the CR INF TSI; for track designed for higher axle loads, harmonised track
loading limits values are not defined.
4.2.3.4.3.
E q u i v a l e n t c o n i c i t y
The range of values of speed and equivalent conicity for which the unit is designed to be stable shall be
specified and recorded in the technical documentation. These values shall be respected for design and in-
service conditions.
The equivalent conicity shall be calculated in accordance with EN15302:2008 for the amplitude (y) of the
wheelset’s lateral displacement:
— y = 3 mm, if
(TG
–
SR)
≥ 7 mm
— y TG – SR – 1
2 , if
5
mm
≤ (TG – SR) < 7 mm
— y = 2 mm, if
(TG
–
SR)
<
5
mm
where TG is the track gauge and SR is the distance between the active faces of the wheelset ( see figure 1).
Units equipped with independently rotating wheels are exempt from the requirements in clause 4.2.3.4.3 of
this TSI.
4.2.3.4.3.1. DESIGN
VALUES
FOR
NEW
WHEEL
PROFILES
This section defines verifications to be performed by calculations in order to ensure that a ‘new wheel’
profile and the distance between active faces of the wheels is suitable for tracks of the TEN network which
comply to the CR Infrastructure TSI.
Wheel profile and the distance between active faces of the wheels (Dimension SR in figure 1, § 4.2.3.5.2.1)
shall be selected to ensure that the equivalent conicity limit set out in table 2 is not exceeded when the
designed wheelset is modelled passing over the representative sample of track test conditions as specified in
table 3.

---

L 139/40
EN
Official Journal of the European Union
26.5.2011
Table 2
Equivalent conicity design limit values
Maximum vehicle
operating speed
Equivalent conicity limit values
Test conditions
(km/h)
(see table 3)
≤ 60 N/A N/A
> 60 and ≤ 190 0,30 All
> 190 Values
specified
in
the
HS
RST
TSI
Conditions specified in the HS RST TSI
apply
apply
Table 3
Track test conditions for equivalent conicity representative of the TEN network
Test condition
number
Rail head profile Rail
inclination Track
gauge
1 Rail
section
60
E
1
defined
in
EN
13674-1:2003 1
in
20 1
435
mm
2 Rail
section
60
E
1
defined
in
EN
13674-1:2003 1
in
40 1
435
mm
3 Rail
section
60
E
1
defined
in
EN
13674-1:2003 1
in
20 1
437
mm
4 Rail
section
60
E
1
defined
in
EN
13674-1:2003 1
in
40 1
437
mm
5 Rail
section
60
E
2
defined
in
EN
13674-
1 in 40 1
435
mm
1: